ScotMesh RNS Network
LilyGO T3S3 (SX127x)
About this board
Maker: LilyGO
Microcontroller: ESP32-S3 Radio: SX1276 / SX1278
Bands: 433 MHz (410–525 MHz), 868 MHz (820–1020 MHz)
Firmware here: RNode firmware 1.86, ScotMesh microReticulum firmware v1.86-scotmesh.6
RNode firmware 1.86
An RNode: a LoRa radio for a computer or phone running Reticulum. The computer or phone sets the radio.
Download
SHA-256: 7167f1c15eb27834c1c5abcc5e182d62af15868f8d9ad89feb38b3dbf3b54252
Easiest: rnodeconf autoinstall, offline
rnodeconf can flash and set up this board in one go without internet, if you give it the firmware and its release hash first. You need rnodeconf and pyserial from the Tools page. Linux and macOS:
mkdir -p ~/.config/rnodeconf/update/1.86
cp rnode_firmware_t3s3_sx127x.zip ~/.config/rnodeconf/update/1.86/
echo "1.86 7167f1c15eb27834c1c5abcc5e182d62af15868f8d9ad89feb38b3dbf3b54252" > ~/.config/rnodeconf/update/1.86/rnode_firmware_t3s3_sx127x.zip.version
rnodeconf /dev/ttyACM0 --autoinstall --nocheck --fw-version 1.86
Windows (Command Prompt):
mkdir "%USERPROFILE%\.config\rnodeconf\update\1.86"
copy rnode_firmware_t3s3_sx127x.zip "%USERPROFILE%\.config\rnodeconf\update\1.86"
echo 1.86 7167f1c15eb27834c1c5abcc5e182d62af15868f8d9ad89feb38b3dbf3b54252> "%USERPROFILE%\.config\rnodeconf\update\1.86\rnode_firmware_t3s3_sx127x.zip.version"
rnodeconf COM3 --autoinstall --nocheck --fw-version 1.86
It asks what the board is and which band, flashes it, then does the provisioning below for you. The rest of this section is for doing it by hand.
Flash it: Linux and macOS
Unzip the firmware into its own folder and run the esptool.py that comes inside it. You need Python 3 with pyserial (Tools page).
mkdir t3s3_sx127x && cd t3s3_sx127x
python3 -m zipfile -e ../rnode_firmware_t3s3_sx127x.zip .
python3 esptool.py --chip esp32s3 --port /dev/ttyACM0
--baud 921600 --before default_reset --after hard_reset
write_flash -z --flash_mode dio --flash_freq 80m
--flash_size 4MB
0x0 rnode_firmware_t3s3_sx127x.bootloader
0x8000 rnode_firmware_t3s3_sx127x.partitions
0xe000 rnode_firmware_t3s3_sx127x.boot_app0
0x10000 rnode_firmware_t3s3_sx127x.bin
0x210000 console_image.bin
On a Mac the port looks like /dev/cu.usbmodem1101. If writing fails at 921600 baud, use --baud 115200.
No Python? Use the standalone esptool from the Tools page: in place of python3 esptool.py, run ../esptool-linux-amd64/esptool (or the folder for your Mac or ARM computer).
Flash it: Windows
Put rnode_firmware_t3s3_sx127x.zip and esptool-v4.12.0-windows-amd64.zip (Tools page) in the same folder, open Command Prompt there (type cmd in the Explorer address bar and press Enter), then:
tar -xf esptool-v4.12.0-windows-amd64.zip
mkdir t3s3_sx127x
tar -xf rnode_firmware_t3s3_sx127x.zip -C t3s3_sx127x
cd t3s3_sx127x
..\esptool-windows-amd64\esptool.exe --chip esp32s3 ^
--port COM3 --baud 921600 --before default_reset ^
--after hard_reset write_flash -z --flash_mode dio ^
--flash_freq 80m --flash_size 4MB ^
0x0 rnode_firmware_t3s3_sx127x.bootloader ^
0x8000 rnode_firmware_t3s3_sx127x.partitions ^
0xe000 rnode_firmware_t3s3_sx127x.boot_app0 ^
0x10000 rnode_firmware_t3s3_sx127x.bin ^
0x210000 console_image.bin
Your port is in Device Manager under Ports (COM & LPT).
Set up the board (provisioning)
The firmware will not start its radio until the board's EEPROM holds what the board is (product, model, hardware revision) and the hash of the firmware you just flashed. How to flash explains why. With rnodeconf installed (Tools):
rnodeconf -k
rnodeconf /dev/ttyACM0 -r --product 03 --model aa --hwrev 1
rnodeconf /dev/ttyACM0 -H 2e97c0809e21c78a3a1206a4d96f67496a751d179678665a8bb41e9f8a45eb38
Model code by band: a5 for 433 MHz (410–525 MHz), aa for 868 MHz (820–1020 MHz). Use the one for your board's band.
The first line makes a signing key; you only need it once on each computer. Skip the second line if the board has been set up before: the EEPROM survives a normal reflash. The third line is needed after every flash. Wait 5 seconds after it before you reset or unplug the board.
On Windows use the COM port instead, for example COM3.
ScotMesh microReticulum firmware v1.86-scotmesh.6
A standalone Reticulum node with its own identity. It needs no computer once it is set up.
Download
SHA-256: 21ad217b79e1f6d086e50404fe47f7a28f1be518bb1823215254dbe5fef82543
Flash it: Linux and macOS
Unzip the firmware into its own folder and run the esptool.py that comes inside it. You need Python 3 with pyserial (Tools page).
mkdir t3s3_sx127x && cd t3s3_sx127x
python3 -m zipfile -e ../rnode_firmware_t3s3_sx127x.zip .
python3 esptool.py --chip esp32s3 --port /dev/ttyACM0
--baud 921600 --before default_reset --after hard_reset
write_flash -z --flash_mode dio --flash_freq 80m
--flash_size 4MB
0x0 rnode_firmware_t3s3_sx127x.bootloader
0x8000 rnode_firmware_t3s3_sx127x.partitions
0xe000 rnode_firmware_t3s3_sx127x.boot_app0
0x10000 rnode_firmware_t3s3_sx127x.bin
On a Mac the port looks like /dev/cu.usbmodem1101. If writing fails at 921600 baud, use --baud 115200.
No Python? Use the standalone esptool from the Tools page: in place of python3 esptool.py, run ../esptool-linux-amd64/esptool (or the folder for your Mac or ARM computer).
The console image is left out on purpose: a ScotMesh node keeps its own data in that part of the flash. To start from scratch (new identity, EEPROM wiped), first run python3 esptool.py --chip esp32s3 --port /dev/ttyACM0 erase_flash and then do the provisioning below in full.
Flash it: Windows
Put rnode_firmware_t3s3_sx127x.zip and esptool-v4.12.0-windows-amd64.zip (Tools page) in the same folder, open Command Prompt there (type cmd in the Explorer address bar and press Enter), then:
tar -xf esptool-v4.12.0-windows-amd64.zip
mkdir t3s3_sx127x
tar -xf rnode_firmware_t3s3_sx127x.zip -C t3s3_sx127x
cd t3s3_sx127x
..\esptool-windows-amd64\esptool.exe --chip esp32s3 ^
--port COM3 --baud 921600 --before default_reset ^
--after hard_reset write_flash -z --flash_mode dio ^
--flash_freq 80m --flash_size 4MB ^
0x0 rnode_firmware_t3s3_sx127x.bootloader ^
0x8000 rnode_firmware_t3s3_sx127x.partitions ^
0xe000 rnode_firmware_t3s3_sx127x.boot_app0 ^
0x10000 rnode_firmware_t3s3_sx127x.bin
Your port is in Device Manager under Ports (COM & LPT).
Set up the board (provisioning)
The firmware will not start its radio until the board's EEPROM holds what the board is (product, model, hardware revision) and the hash of the firmware you just flashed. How to flash explains why. With rnodeconf installed (Tools):
rnodeconf -k
rnodeconf /dev/ttyACM0 -r --product 03 --model aa --hwrev 1
rnodeconf /dev/ttyACM0 -H 9dd011caf3f0f6fc5d43b0105b0d2f89085da75206bca134b530d9572f3e41ae
Model code by band: a5 for 433 MHz (410–525 MHz), aa for 868 MHz (820–1020 MHz). Use the one for your board's band.
The first line makes a signing key; you only need it once on each computer. Skip the second line if the board has been set up before: the EEPROM survives a normal reflash. The third line is needed after every flash. Wait 5 seconds after it before you reset or unplug the board.
On Windows use the COM port instead, for example COM3.
Put it on the air
A standalone node needs its radio settings. With internet, the web flasher at rnode.scotmesh.net (Reconfigure) or the RNode Console will set it up, including the node's name and admin settings. Without internet, rnodeconf stores the radio settings and switches the node into transport mode, which is what the web flasher does over USB:
ScotMesh 868 (869.462 MHz, 125 kHz, SF9, 4/5, 17 dBm):
rnodeconf /dev/ttyACM0 -T --freq 869462500 --bw 125000 --txp 17 --sf 9 --cr 5
ScotMesh 433 (433.775 MHz, 125 kHz, SF8, 4/5, 7 dBm):
rnodeconf /dev/ttyACM0 -T --freq 433775000 --bw 125000 --txp 7 --sf 8 --cr 5
These are the ScotMesh profiles. Other ScotMesh nodes will only hear you if yours match.